FWS2400ss WASTE COMPACTOR
Marine /Commercial Waste Compactor

Purpose
The FWS1800ss Waste Compactor is used for the volume reduction of mixed Waste, being compacted into either a heavy duty plastic bag or a strong non-synthetic box.

Mixed Waste can be taken as follows:  Cardboard Paper - Aluminium; Plastic - Food - Cloth - Wood - Glass - Other.

The operation of the Waste Compactor is not adversely effected if the Waste is wet (up to 10% water by weight)

Identity
The major components of the Compactor are a hydraulic pump/motor,pressure switch, transformer, control module, sterilization lamp and air filtration unit

Services Required
Electrical power at 240 / 380 / 440 V, 60  Hz, 3-phase, 3-wire (all voltages  accommodated)

Design and Performance Data Construction :  
Mainframe - High Tensile  Steel / External  panels - 304 Stainless Steel

Watertightness Standard
The upper service compartment enclosure  is to IP55 standard (spray-proof).

Weight
With Re-use-a-cube 303 kg

Dimensions
Height - Cabinet 1933mm
C/w mounting feet 2032mm
Width 714mm
Depth 706mm
Size of loading chute opening (S/S) 609 x  482mm
Cube size 590x610x450mm
Cube size (compacted) 0.170m3

Space Required
Appox. 0.485m2

Performance Data
Compaction force 6250 kg
Cycle time 18 - 22 seconds
Motor /Pump Unit 1/2 hp

Weight of Compacted Waste
Approx. 0.06 C.Y. (46m3 15.87/45.4Kg) av. weight (wet waste will weight more). A 'Full Loading Lamp' will let you know when the compacted load is ready for removal (control of the waste cube weight is made by adjustment to the Limit switch in the upper chamber)

Maintenance
All services to the unit are early accessed

Logistic
Requirements Clean warm soapy water is required for cleaning the Compactor

Compaction Ratio Guide
Volume : Approx 1.1 C.Y. (1.683 ) of loose dry waste @ 20/1 Compaction ration (compaction variations on types of waste )

  FWS1800ss WASTE COMPACTOR
  Marine /Commercial Waste Compactor

Purpose
The FWS1800ss Waste Compactor is used for the volume reduction of mixed Waste, being compacted into either a heavy duty plastic bag or a strong non-synthetic box. Mixed Waste can be taken as follows: Cardboard/Paper - Aluminium - Plastic - Food - Cloth - Wood - Glass - Other.The operation of the Compactor is not adversely effected if the Garbage is wet (up to 10% water by weight).

Identity
The major components of the Waste Compactor are a hydraulic pump/motor,pressure switch , transformer , control module, sterilization lamp and air filtration unit.

Services
Required Electrical power at 240 / 380 / 440 V, 60  Hz,  3- phase, 3-wire.(all voltages accommodated)

Design and Performance Data
Construction: Mainframe - High Tensile Steel
External panels - 304 Stainless Steel

Watertightness Standard
The upper service compartment enclosure is to IP55 standard (spray-proof).

Weight
Shipping 280 kg

Dimensions
Height - Cabinet 1717.55mmC/w
mounting feet 1806.45mm
Width 624.84mm
Depth 553.97mm
Floor space 0.36m2
Floor space (service door open) 0.72m2
Size of loading chamber opening (Stainless Steel) 527 x 380mm
Cube size 510 x 450 x 420mm
Cube size (compacted) 0.099m3

Space Required
Appox. 0.313m2

Performance Data
Compaction force 6250 kg
Motor /Pump Unit 1/2 hp
Cycle time 18 - 22 seconds
Volume : Approx 1.1 C.Y. (1.683 ) of loose dry waste @ 20/1 Compaction ration  (compaction variations on types of waste)

Weight of Compacted Waste
Approx. 0.06 C.Y. (46m3 15.87/45.4Kg) av. weight (wet waste will weight more). A 'Full  Loading Lamp' will let you know when the compacted load is ready for removal (control of the waste cube weight is made by adjustment to the Limit switch in the upper chamber)

Logistic Requirements
Clean warm soapy water is required for cleaning the Waste Compactor

Monthly
Grease guide rods
Check hydraulic fluid level
Check for fluid leaks Tighten guide rods and cylinder nuts
Check function of door switches

Six Monthly
Replace UV sterilization lamp
Replace particle and charcoal filter packs
Check quality of hydraulic fluid

Annually
Check correct function of all electrical switchgear
Check insulation reading on motor
Reset compaction pressure setting
Check floor mounts for tightness

Bi-Annually
Replace hydraulic fluid - ISO grade 32 or 46
Replace door switches
Replace limit switches

General
The Waste Compaction cube will need replacing from time to time, but this is very dependent on the use and whether boxes are used in conjunction. The Compaction chamber should be cleaned every time the cube is removed, to prevent the build up of Waste on the plate.

The external and internal faces of the machine only need to be wiped with a cloth.

The area around the UV sterilization lamp should be kept free from Waste and the housing cleaned when the lamp is changed.

top of page